請教一個Fire Enclosure的問題!!
我的產品在申請UL60065時,Rating為120V,30W.塑料外殼的材料需要V-1以上嗎?標準在哪里有說到?請大家?guī)兔?謝謝!!
全部回復(12)
正序查看
倒序查看
依 UL 60065 :
20.2 FIRE ENCLOSURE
20.2.1 DU Each of the following shall be contained in a FIRE ENCLOSURE:
(1) circuits and their associated components where the AVAILABLE POWER exceeds 15 W,
(2) inductors and windings CONDUCTIVELY CONNECTED TO THE MAINS, and
(3) apparatus with open circuit voltages exceeding 4 kV (peak) a.c. or d.c., under normal operating conditions.
The
FIRE ENCLOSURE shall comply with the flammability category in table 22 according to UL 94 or UL 746C as specified.
Polymeric:
a) apparatus using high voltage components a
MAJOR ENCLOSURE PART V-0
Parts other than MAJOR ENCLOSURE PARTS V-1 or V-0
b) commercial audio STATIONARY APPARATUS and PERMANENTLY CONNECTED APPARATUS 5VA
c) other than apparatus itemized in a) and b) above a V-2, V-1 or V-0
20.2 FIRE ENCLOSURE
20.2.1 DU Each of the following shall be contained in a FIRE ENCLOSURE:
(1) circuits and their associated components where the AVAILABLE POWER exceeds 15 W,
(2) inductors and windings CONDUCTIVELY CONNECTED TO THE MAINS, and
(3) apparatus with open circuit voltages exceeding 4 kV (peak) a.c. or d.c., under normal operating conditions.
The
FIRE ENCLOSURE shall comply with the flammability category in table 22 according to UL 94 or UL 746C as specified.
Polymeric:
a) apparatus using high voltage components a
MAJOR ENCLOSURE PART V-0
Parts other than MAJOR ENCLOSURE PARTS V-1 or V-0
b) commercial audio STATIONARY APPARATUS and PERMANENTLY CONNECTED APPARATUS 5VA
c) other than apparatus itemized in a) and b) above a V-2, V-1 or V-0
0
回復
@mikesu
依UL60065:20.2FIREENCLOSURE20.2.1DUEachofthefollowingshallbecontainedinaFIREENCLOSURE:(1)circuitsandtheirassociatedcomponentswheretheAVAILABLEPOWERexceeds15W,(2)inductorsandwindingsCONDUCTIVELYCONNECTEDTOTHEMAINS,and(3)apparatuswithopencircuitvoltagesexceeding4kV(peak)a.c.ord.c.,undernormaloperatingconditions.TheFIREENCLOSUREshallcomplywiththeflammabilitycategoryintable22accordingtoUL94orUL746Casspecified.Polymeric:a)apparatususinghighvoltagecomponentsaMAJORENCLOSUREPARTV-0PartsotherthanMAJORENCLOSUREPARTSV-1orV-0b)commercialaudioSTATIONARYAPPARATUSandPERMANENTLYCONNECTEDAPPARATUS5VAc)otherthanapparatusitemizedina)andb)aboveaV-2,V-1orV-0
a),b),c)3條分別是說的哪些產品?
a)中,high voltage是指4KV嗎?
a)中,high voltage是指4KV嗎?
0
回復
@williamhu
a),b),c)3條分別是說的哪些產品?a)中,highvoltage是指4KV嗎?
UL 60065 在 Fire Enclosure 要求較 IEC 60065 有所不同.
其中 :
(1) 使用功率大於 30 W 以上....
你的 電源 30 W 已高於 UL 60065 要求, 故需有 Fire Enclosure. 至於該 Fire Enclosure 的材質要求, 正如 Barry 所解說 (A)~(C) 在不同應用下防火材質等級要求.
60065 這本標準我還沒讀完............... 汗.....
以上...
其中 :
(1) 使用功率大於 30 W 以上....
你的 電源 30 W 已高於 UL 60065 要求, 故需有 Fire Enclosure. 至於該 Fire Enclosure 的材質要求, 正如 Barry 所解說 (A)~(C) 在不同應用下防火材質等級要求.
60065 這本標準我還沒讀完............... 汗.....
以上...
0
回復
@hy_barry
請教一下mikesu兄,這個30W的限制在哪可以看到.我的這本UL6500-1999有很多刪節號,看得不舒服.
據我所知,UL的標準里,關于enclosure的要求,都統一跟從UL746C(可能一些與IEC合并的標準例外). 根據UL746C,凡>42.4V peak voltage (30 V RMS)的電壓都視為可能導致著火或觸電.
3.34 RISK OF ELECTRIC SHOCK – A risk of electric shock is considered to exist at any part if,
a) The potential between the part and earth ground or any other accessible part is more than
42.4 V peak, and
b) The continuous current flow through a 1500 ohm resistor connected across the potential
exceeds 0.5 mA.
3.35 RISK OF FIRE – A risk of fire is considered to exist at any two points in a circuit where;
a) The open circuit voltage is more than 42.4 V peak and the energy available to the circuit
under any condition of load including short circuit, results in a current of 8 A or more after 1
minute of operation, or
b) A power of more than 15 watts can be delivered into an external resistor connected between
the two points.
3.34 RISK OF ELECTRIC SHOCK – A risk of electric shock is considered to exist at any part if,
a) The potential between the part and earth ground or any other accessible part is more than
42.4 V peak, and
b) The continuous current flow through a 1500 ohm resistor connected across the potential
exceeds 0.5 mA.
3.35 RISK OF FIRE – A risk of fire is considered to exist at any two points in a circuit where;
a) The open circuit voltage is more than 42.4 V peak and the energy available to the circuit
under any condition of load including short circuit, results in a current of 8 A or more after 1
minute of operation, or
b) A power of more than 15 watts can be delivered into an external resistor connected between
the two points.
0
回復
@hy_barry
請教一下mikesu兄,這個30W的限制在哪可以看到.我的這本UL6500-1999有很多刪節號,看得不舒服.
在 UL 60065
20.2.1 DU Each of the following shall be contained in a FIRE ENCLOSURE:
(1) circuits and their associated components where the AVAILABLE POWER exceeds 15 W,
(2), (3)
上面這句話, 我的理解是
"20.2.1 以下架構均需容納 Fire Enclosure 內"
(1) 該線路或相關零件/附件使用功率大於 15 W.
(2) 電感/線圈連接於 市電.
(3) 電壓高於 4 kV
UL60065 在這段全面都有刪節/增改 IEC60065 條文... (畢竟 UL 有 UL 1492 的包袱, 就像當年 UL 478 轉 UL 1950 D2 D3 差異一般). 糟...... 這會不會透露年齡.........
Barry , 很高興認識你. .....
20.2.1 DU Each of the following shall be contained in a FIRE ENCLOSURE:
(1) circuits and their associated components where the AVAILABLE POWER exceeds 15 W,
(2), (3)
上面這句話, 我的理解是
"20.2.1 以下架構均需容納 Fire Enclosure 內"
(1) 該線路或相關零件/附件使用功率大於 15 W.
(2) 電感/線圈連接於 市電.
(3) 電壓高於 4 kV
UL60065 在這段全面都有刪節/增改 IEC60065 條文... (畢竟 UL 有 UL 1492 的包袱, 就像當年 UL 478 轉 UL 1950 D2 D3 差異一般). 糟...... 這會不會透露年齡.........
Barry , 很高興認識你. .....
0
回復
@me_chkaa
據我所知,UL的標準里,關于enclosure的要求,都統一跟從UL746C(可能一些與IEC合并的標準例外).根據UL746C,凡>42.4Vpeakvoltage(30VRMS)的電壓都視為可能導致著火或觸電.3.34RISKOFELECTRICSHOCK–Ariskofelectricshockisconsideredtoexistatanypartif,a)Thepotentialbetweenthepartandearthgroundoranyotheraccessiblepartismorethan42.4Vpeak,andb)Thecontinuouscurrentflowthrougha1500ohmresistorconnectedacrossthepotentialexceeds0.5mA.3.35RISKOFFIRE–Ariskoffireisconsideredtoexistatanytwopointsinacircuitwhere;a)Theopencircuitvoltageismorethan42.4Vpeakandtheenergyavailabletothecircuitunderanyconditionofloadincludingshortcircuit,resultsinacurrentof8Aormoreafter1minuteofoperation,orb)Apowerofmorethan15wattscanbedeliveredintoanexternalresistorconnectedbetweenthetwopoints.
謝謝me_chkaa兄的回復.
在UL60065-1999中,只說明了防火外殼的分類和厚類要求要遵循UL746C和UL94,并沒有說60065防火外殼的適用條件和UL746C相同.
有什么不同意見盡請?zhí)岢?
在UL60065-1999中,只說明了防火外殼的分類和厚類要求要遵循UL746C和UL94,并沒有說60065防火外殼的適用條件和UL746C相同.
有什么不同意見盡請?zhí)岢?
0
回復
@mikesu
在UL6006520.2.1DUEachofthefollowingshallbecontainedinaFIREENCLOSURE:(1)circuitsandtheirassociatedcomponentswheretheAVAILABLEPOWERexceeds15W,(2),(3)上面這句話,我的理解是"20.2.1以下架構均需容納FireEnclosure內"(1)該線路或相關零件/附件使用功率大於15W.(2)電感/線圈連接於市電.(3)電壓高於4kVUL60065在這段全面都有刪節/增改IEC60065條文...(畢竟UL有UL1492的包袱,就像當年UL478轉UL1950D2D3差異一般).糟......這會不會透露年齡.........Barry,很高興認識你......
mikesu,謝謝你的回復,我也很高興認識你.從你的多次回貼中可以看出mikesu兄的安規功底很深,以后還要多多向你請教.
你的理解是準確的.只是這段話加了下劃線,不知是什么意思?
我也是從UL1950開始的,那時的安規環境沒現在好,當時拿到UL1950時都看不懂,花了一個月的時間來讀標準(查詞典呵),頭都讀大了.
你的理解是準確的.只是這段話加了下劃線,不知是什么意思?
我也是從UL1950開始的,那時的安規環境沒現在好,當時拿到UL1950時都看不懂,花了一個月的時間來讀標準(查詞典呵),頭都讀大了.
0
回復
@hy_barry
mikesu,謝謝你的回復,我也很高興認識你.從你的多次回貼中可以看出mikesu兄的安規功底很深,以后還要多多向你請教.你的理解是準確的.只是這段話加了下劃線,不知是什么意思?我也是從UL1950開始的,那時的安規環境沒現在好,當時拿到UL1950時都看不懂,花了一個月的時間來讀標準(查詞典呵),頭都讀大了.
下劃線的意思是在UL60065里面有這樣的要求,但是在IEC60065沒有這樣的要求,在UL標準里面有下劃線和刪除線,下劃線就是我上面說的意思,刪除線的意思是在IEC里面有這樣的要求,但是UL沒有.
謝謝大家都這個問題的討論,通過大家的意見,我對Fire Enclosure有更深的了解了,謝謝!!
謝謝大家都這個問題的討論,通過大家的意見,我對Fire Enclosure有更深的了解了,謝謝!!
0
回復
