關于PROTEL99SE的“gerber”轉換問題
我前些天試做過一次PCB,而且也成功了,可在我取板子的時候,那位作板子的人說廠家要求將“XXX.PCB”的文件轉換成“gerber”文件,我問他怎樣轉,他說他也不知道,廠家就這么要求,在網上也查不到,請教各位老師,怎樣將“XXX.PCB”文件轉換成“gerber”文件?謝謝
全部回復(17)
正序查看
倒序查看
@夜鷹
首先謝謝您,可我打開后FILE里找不到CAMMANAGER,我用的99SE是經過漢化的,這有影響嗎?再次謝謝
不會吧!可以看一下圖片。
500) {this.resized=true; this.width=500; this.alt='這是一張縮略圖,點擊可放大。\n按住CTRL,滾動鼠標滾輪可自由縮放';this.style.cursor='hand'}" onclick="if(!this.resized) {return true;} else {window.open('http://u.dianyuan.com/bbs/u/25/1106956726.jpg');}" onmousewheel="return imgzoom(this);">

0
回復
@碧海銀沙
不會吧!可以看一下圖片。[圖片]500){this.resized=true;this.width=500;this.alt='這是一張縮略圖,點擊可放大。\n按住CTRL,滾動鼠標滾輪可自由縮放';this.style.cursor='hand'}"onclick="if(!this.resized){returntrue;}else{window.open('http://u.dianyuan.com/bbs/u/25/1106956726.jpg');}"onmousewheel="returnimgzoom(this);">
上樓的兄弟可否把操作說清楚.謝謝!!
0
回復
@碧海銀沙
不會吧!可以看一下圖片。[圖片]500){this.resized=true;this.width=500;this.alt='這是一張縮略圖,點擊可放大。\n按住CTRL,滾動鼠標滾輪可自由縮放';this.style.cursor='hand'}"onclick="if(!this.resized){returntrue;}else{window.open('http://u.dianyuan.com/bbs/u/25/1106956726.jpg');}"onmousewheel="returnimgzoom(this);">
我裝的99SE的FILE文件下:
500) {this.resized=true; this.width=500; this.alt='這是一張縮略圖,點擊可放大。\n按住CTRL,滾動鼠標滾輪可自由縮放';this.style.cursor='hand'}" onclick="if(!this.resized) {return true;} else {window.open('http://u.dianyuan.com/bbs/u/25/1107086185.gif');}" onmousewheel="return imgzoom(this);">

0
回復
@碧海銀沙
PROTEL99SE有個SP6補丁,不知是否是沒有這個的緣故!另外,還有個孔徑編輯補丁。
你說的是它嗎?
500) {this.resized=true; this.width=500; this.alt='這是一張縮略圖,點擊可放大。\n按住CTRL,滾動鼠標滾輪可自由縮放';this.style.cursor='hand'}" onclick="if(!this.resized) {return true;} else {window.open('http://u.dianyuan.com/bbs/u/26/1107791430.gif');}" onmousewheel="return imgzoom(this);">

0
回復
@碧海銀沙
PROTEL99SE有個SP6補丁,不知是否是沒有這個的緣故!另外,還有個孔徑編輯補丁。

你說的“孔徑編輯補丁”在哪?
0
回復