我們是采用鄭州中景圓的0.96寸的oled屏，單片機為stm32F103，通訊方式是三線SPI，下面是屏的簡單介紹

主要由裸屏和底板PCB組成，裸屏由SSD1306驅動，這也是一種較為廣泛使用的led驅動芯片。

得到一塊新的屏幕，最重要的就是看能否點亮，點亮了才能使用做各種顯示應用。就是需要SPI驅動程序移植一下，問題不大。

1.配置SPI，初始化，采用硬件SPI方式驅動

GPIO_InitTypeDef  GPIO_InitStructure;
	SPI_InitTypeDef SPI_InitStructure;
	
//	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB, ENABLE);
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);//使能SPI1時鐘
	
	
	/* 配置OLED_DC(PA6),OLED_RST(PA4) */
 	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA,ENABLE);
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6|GPIO_Pin_4;	
 	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; 		 
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
 	GPIO_Init(GPIOA, &GPIO_InitStructure);
	
	/* 配置SPI1的 SCK(PA5),MOSI(PA7)引腳 */ 
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5| GPIO_Pin_7; 
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_Init(GPIOA, &GPIO_InitStructure);

	SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;	/* 設置SPI單向或者雙向的數據模式 */
	SPI_InitStructure.SPI_Mode = SPI_Mode_Master;		/* 設置SPI工作模式:設置為主SPI */
	SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;	/* 設置SPI的數據大小:SPI發送接收8位幀結構 */
	SPI_InitStructure.SPI_CPOL = SPI_CPOL_High;			/* 選擇了串行時鐘的穩態:時鐘懸空低 */
	SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;		/* 數據捕獲于第二個時鐘沿 */
	SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;			/* NSS信號由硬件（NSS管腳）還是軟件（使用SSI位）管理:內部NSS信號有SSI位控制 */
	SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_4;	/* 定義波特率預分頻的值:波特率預分頻值為4 */
	SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;	/* 指定數據傳輸從MSB位還是LSB位開始:數據傳輸從MSB位開始 */
	SPI_InitStructure.SPI_CRCPolynomial = 0;			/* CRC值計算的多項式*/
	SPI_Init(SPI1, &SPI_InitStructure); 				/* 根據SPI_InitStruct中指定的參數初始化外設SPIx寄存器 */
 
	SPI_Cmd(SPI1, ENABLE); /* 使能SPI外設 */
	
	//OLED_CS=1;
//	OLED_RS=1;
    OLED_RST=1; 
	delay_ms(100);
	
	OLED_RST=0;
	delay_ms(100);
	OLED_RST=1; 

采用硬件SPI的方式，不用IO口來模擬SPI的時序了，但是OLED屏上電后需要相關的設置，都是廠家提供的初始化代碼

2.如何點亮OLED并顯示呢

需要通過取模軟件PCtoLCD2002取出你想要的漢字，比如字體大小等都可以設置，我們顯示電子星球

并建立多維數組，存儲字模，

const unsigned char Hzk[][16] = {
 {0x00,0x00,0xF8,0xF8,0x88,0x88,0x88,0xFF,0xFF,0x88,0x88,0x88,0xF8,0xF8,0x00,0x00},
{0x00,0x00,0x1F,0x1F,0x08,0x08,0x08,0x7F,0xFF,0x88,0x88,0x88,0x9F,0x9F,0xF0,0xF0},/*"電",0*/

{0x80,0x82,0x82,0x82,0x82,0x82,0x82,0xE2,0xE2,0xB2,0x9A,0x8E,0x86,0x82,0x80,0x80},
{0x00,0x00,0x00,0x00,0x00,0x40,0xC0,0xFF,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"子",1*/

{0x00,0x00,0x00,0xBE,0xBE,0x2A,0x2A,0xEA,0xEA,0x2A,0x2A,0x3E,0x3E,0x00,0x00,0x00},
{0x00,0x44,0x46,0x4B,0x49,0x49,0x49,0x7F,0x7F,0x49,0x49,0x49,0x49,0x41,0x40,0x00},/*"星",2*/

{0x04,0x84,0x84,0xFC,0xFC,0x84,0x94,0x50,0xD0,0x90,0xFF,0xFF,0x91,0x17,0x96,0x90},
{0x20,0x60,0x60,0x3F,0x1F,0x10,0x10,0x18,0x4D,0xC7,0xFF,0x7F,0x07,0x0F,0x19,0x10},/*"球",3*/

主函數調用SPI寫函數就可以了

同樣的方法顯示welcome，看最后顯示效果